|
|  |
| Notices |
Welcome to the sSnakeSs community. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us.
|
12-18-13, 01:14 PM
|
#1
|
|
Member
Join Date: Jan-2013
Posts: 974
Country:
|
Re: sav stay in burrow all day
Hi, is this a Powersun MVB? It isn`t only the UVB irradiation that needs to be taken into account, it`s also the heat, exactly how far from the surface of the bulb to the closest surface of the animal is it?
If this is a Powersun, there are reports that the amount of UVB is much less than the manufacturer claims (at least in the American bulbs and perhaps also Canadian)? You really need a Solar meter to check.
Edit: An MVB like the Powersun has a beam radius of around 75cm at a height of 30cm, in which case it would easily have covered the whole body.
Personally I would recommend using the T5 HO (high output) fluorescent tubes (UVB), then the halogen floods as basking lights.
Check out the 12% UVB tube rather than the 6%...
Arcadia T5 reptile lamps 6% D3+
Last edited by murrindindi; 12-18-13 at 01:27 PM..
|
|
|
12-18-13, 01:32 PM
|
#2
|
|
Member
Join Date: Mar-2013
Posts: 438
Country:
|
Re: sav stay in burrow all day
Quote:
Originally Posted by murrindindi
Hi, is this a Powersun MVB? It isn`t only the UVB irradiation that needs to be taken into account, it`s also the heat, exactly how far from the surface of the bulb to the closest surface of the animal is it?
If this is a Powersun, there are reports that the amount of UVB is much less than the manufacturer claims (at least in the American bulbs and perhaps also Canadian)? You really need a Solar meter to check.
|
Hi this is the powersun 160Watt. To get a 160F surface temp on the floor, the bulb is 5.5 - 6 inches away from the floor, I measured it with tape measure plus a temp gun. The 50 watt right next to it is 2-3 inches higher to produce similar surface temp. So I'm wondering since the monitor's body is thick, would this mean the bulb is too close. It seem to enjoy basking under that temp for 20-30 mins in the morning, then after that it only uses it for short periods. Then it lays somewhere else most of the time or goes in it's burrow.
For my tegu I'm using the same setup(with just the MVB tho) since his halogen floods got shotted(bad wiring on my part) But the tegu is functioning real well under this same setting. The only difference in the 2 animals is that my tegu would dig a burrow himself, however the sav needed me to make a surface on the ground and he will dig to live under the wood, but he does not make tunnels. The soil/sand mix is the same for both animals. 70% soil and 30% sand...
I just got a humidimeter and it says 75% humidity in the middle of the cage, lower than I had expected. It used to be 80%+ even 90% sometimes. It could be due to my house haing the furnace on more now that it's winter...
Not sure what else info I can give. I measured him today he is 2 feet 8 inches. Roughly, since he won't stay still when I was measuring him, keeps thinking I'll give him food.
Last edited by nepoez; 12-18-13 at 01:41 PM..
|
|
|
12-18-13, 01:35 PM
|
#3
|
|
Member
Join Date: Mar-2013
Posts: 438
Country:
|
Re: sav stay in burrow all day
murrindindi, Honestly I didn't get the MVB for the purpose of UVB. I got it in a panic to try to get a bulb setup that would cover his whold body for the sake of basking purpose not so much UVB. UVB would just be a bonus. But right now I don't think UVB is his problem, and my prime suspect was basking site error, thus the MVB I bought. So he's been using that for 2 days now + a extra 50w halogen flood. I don't seen any improvements, dispite the high basking temps...
Quote:
Originally Posted by murrindindi
Hi, is this a Powersun MVB? It isn`t only the UVB irradiation that needs to be taken into account, it`s also the heat, exactly how far from the surface of the bulb to the closest surface of the animal is it?
If this is a Powersun, there are reports that the amount of UVB is much less than the manufacturer claims (at least in the American bulbs and perhaps also Canadian)? You really need a Solar meter to check.
Edit: An MVB like the Powersun has a beam radius of around 75cm at a height of 30cm, in which case it would easily have covered the whole body.
Personally I would recommend using the T5 HO (high output) fluorescent tubes (UVB), then the halogen floods as basking lights.
Check out the 12% UVB tube rather than the 6%...
Arcadia T5 reptile lamps 6% D3+
|
|
|
|
12-18-13, 02:13 PM
|
#4
|
|
Member
Join Date: Jan-2013
Posts: 974
Country:
|
Re: sav stay in burrow all day
Quote:
Originally Posted by nepoez
murrindindi, Honestly I didn't get the MVB for the purpose of UVB. I got it in a panic to try to get a bulb setup that would cover his whold body for the sake of basking purpose not so much UVB. UVB would just be a bonus. But right now I don't think UVB is his problem, and my prime suspect was basking site error, thus the MVB I bought. So he's been using that for 2 days now + a extra 50w halogen flood. I don't seen any improvements, dispite the high basking temps...
|
It doesn`t matter whether you used the MVB for the UVB, heat or just illumination, it MUST be at LEAST 30cm from the face of the bulb to the closest surface of the monitor (which will normally mean it`s head), even slightly closer can cause very serious burns.
I`m not disagreeing with Mark (MDF) or anyone else just for the sake of it, but offering a surface temp of 160f will NOT necessarily cause the animal to lose weight or become more active throughout the day. It will only decrease the time it takes to get the core temp up to "activity level" by a very small amount, maybe a couple of minutes or so (obviously the actual speed will depend on the monitor`s mass).
Unless you can achieve that raised surface temp without also raising the ambient too much must also be taken into consideration (if it`s too warm they retreat), in which case they`ll cool down, become less active, defeating the purpose of raising it in the first place! This species is most active during the cooler wet season when ambient temps don`t usually get "extreme".
Other species DO encounter higher ambient and surface temps and use them very regularly, I`m not suggesting raising them is a bad thing in itself, but 140f is perfectly acceptable and should ensure the monitor can operate at it`s full potential, providing all the other parameters are met.
EDIT: Can you take a video of the monitor?
Last edited by murrindindi; 12-18-13 at 02:18 PM..
|
|
|
12-18-13, 02:19 PM
|
#5
|
|
Member
Join Date: Mar-2013
Posts: 438
Country:
|
Re: sav stay in burrow all day
OK in this case I will need more help again. Currently for any of my bulbs to make the ground's surface temp to be 140F, it has to be only 5-10 inches away. e.g. 50 watt halogen needs to be 10 inches from the ground, or maybe less, to reach 140F on the floor. And the MVB needs to be 5 inches away form the ground to reach 140F on the ground.
If you say the light bulb must be 30cm from bulb to ANIMAL, then I can't possibliy achieve 140F on the floor surface. So I am really confused now what I should do. Please advice. Sorry I'm a person that needs great details when explaining what to do so please be patient.
Quote:
Originally Posted by murrindindi
It doesn`t matter whether you used the MVB for the UVB, heat or just illumination, it MUST be at LEAST 30cm from the face of the bulb to the closest surface of the monitor (which will normally mean it`s head), even slightly closer can cause very serious burns.
I`m not disagreeing with Mark (MDF) or anyone else just for the sake of it, but offering a surface temp of 160f will NOT necessarily cause the animal to lose weight or become more active throughout the day. It will only decrease the time it takes to get the core temp up to "activity level" by a very small amount, maybe a couple of minutes or so (obviously the actual speed will depend on the monitor`s mass).
Unless you can achieve that raised surface temp without also raising the ambient too much must also be taken into consideration (if it`s too warm they retreat), in which case they`ll cool down, become less active, defeating the purpose of raising it in the first place! This species is most active during the cooler wet season when ambient temps don`t usually get "extreme".
Other species DO encounter higher ambient and surface temps and use them very regularly, I`m not suggesting raising them is a bad thing in itself, but 140f is perfectly acceptable and should ensure the monitor can operate at it`s full potential, providing all the other parameters are met.
|
|
|
|
| Thread Tools |
|
|
| Display Modes |
Hybrid Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 01:03 AM.
Powered by vBulletin® ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 2002-2026, Hobby Solutions.
|
 |