border
sSNAKESs : Reptile Forum
 

Go Back   sSNAKESs : Reptile Forum > Python Forums > Python Regius

Notices

Closed Thread
 
Thread Tools Display Modes
Old 06-09-13, 08:16 AM   #1
bcr229
Member
 
bcr229's Avatar
 
Join Date: Feb-2013
Location: Eastern WV Panhandle
Posts: 270
Country:
Re: Ball Python Temperature Requirements

Quote:
Originally Posted by Lankyrob View Post
The reading on the thermostat is irrelevant, the temperature where the snake is is what is important
Exactly. On our rack the thermostat is set to 92*F but the reading inside the tub is 90*F on the hot side.
__________________
I buy the kid a pony, she asks for a snake! If only I'd known...
bcr229 is offline  
Login to remove ads
Old 06-09-13, 09:04 AM   #2
Mikoh4792
Member
 
Mikoh4792's Avatar
 
Join Date: May-2013
Posts: 4,858
Country:
Re: Ball Python Temperature Requirements

Quote:
Originally Posted by bcr229 View Post
Exactly. On our rack the thermostat is set to 92*F but the reading inside the tub is 90*F on the hot side.
Is your heat tape recessed into the bottom? Or does the tub come in contact with the heat tape?

I currently have an RBI Iris sweaterbox rack with recessed heat tape. It's about 1/2 inch away from the tub so maybe that is why I have to set it so high to get the desired temps.
Mikoh4792 is offline  
Old 06-10-13, 11:24 AM   #3
bcr229
Member
 
bcr229's Avatar
 
Join Date: Feb-2013
Location: Eastern WV Panhandle
Posts: 270
Country:
Re: Ball Python Temperature Requirements

Quote:
Originally Posted by mikoh4792 View Post
Is your heat tape recessed into the bottom? Or does the tub come in contact with the heat tape?

I currently have an RBI Iris sweaterbox rack with recessed heat tape. It's about 1/2 inch away from the tub so maybe that is why I have to set it so high to get the desired temps.
My husband built the rack. The heat tape sits on the shelf, and the tub is in direct contact with the tape. If you have a half inch air gap between the tape and the tub that will make a huge difference.

Was there a reason given by the manufacturer for recessing the tape? With a half inch air gap, the tape is going to heat more of your air than the tub.
__________________
I buy the kid a pony, she asks for a snake! If only I'd known...
bcr229 is offline  
Old 06-10-13, 11:52 AM   #4
Mikoh4792
Member
 
Mikoh4792's Avatar
 
Join Date: May-2013
Posts: 4,858
Country:
Re: Ball Python Temperature Requirements

Quote:
Originally Posted by bcr229 View Post
My husband built the rack. The heat tape sits on the shelf, and the tub is in direct contact with the tape. If you have a half inch air gap between the tape and the tub that will make a huge difference.

Was there a reason given by the manufacturer for recessing the tape? With a half inch air gap, the tape is going to heat more of your air than the tub.
I think for safety reasons, whatever they may be. I did wish that the tub directly rested on the heat tape, this way I wouldn't have to set it so high. Also as you stated I could have a more concentrated hot spot and leave a considerably cooler cold side inside the tub.

Some pictures to give an idea



Mikoh4792 is offline  
Old 06-10-13, 03:31 PM   #5
Aaron_S
Forum Moderator
 
Aaron_S's Avatar
 
Join Date: Nov-2002
Location: Toronto
Age: 41
Posts: 16,978
Send a message via MSN to Aaron_S
Re: Ball Python Temperature Requirements

Quote:
Originally Posted by bcr229 View Post
My husband built the rack. The heat tape sits on the shelf, and the tub is in direct contact with the tape. If you have a half inch air gap between the tape and the tub that will make a huge difference.

Was there a reason given by the manufacturer for recessing the tape? With a half inch air gap, the tape is going to heat more of your air than the tub.
I router my boards. You should not have the plastic sitting on the heat tape. It doesn't wear out with the sliding over the bins and such so less error.

Mine glides right over everything.
Aaron_S is offline  
Login to remove ads
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:22 AM.

Powered by vBulletin®
©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 2002-2026, Hobby Solutions.

right