border
sSNAKESs : Reptile Forum
 

Go Back   sSNAKESs : Reptile Forum > Enclosure Creation Forums > General Enclosure Discussion

Notices

Closed Thread
 
Thread Tools Display Modes
Old 02-10-18, 03:32 AM   #1
Roman
Member
 
Join Date: Sep-2012
Posts: 329
Country:
Re: Want to build adult bioactive vivarium for brb

I use only metal halide lights or halogen lights as heat sources for my enclosures, from 25 W to 70 W depending on the size of the enclosure. The reasoning behind this is that they create a bright hot spot. Your snake associates warmth with light, so it will look for heat at the brightest spot in your enclosure.

For your enclosure I would use a LED light as long as your enclosure (4 ft) for the ambient light and for your plants. You need enough light in the blue and red spectrum for your plants, so look for a light with 6500k. For heat and UVB place a 70W UV emitting metal halide lamp on top of your enclosure over some mesh. This lamp will provide a heat spot of ca. 30°C/86°F and creates a thermal gradient to the other end of your enclosure where the temperature will be room temperature (or slightly higher). Here in Germany we have a brand of lights which also offers a “flood” version with a wider focus, so the heat and UVB are not tightly focused but a bit wider spread.

Whether you need any additional heating depending on your ambient room temperatures (especially during winter). If your temperatures doesn’t drop below ca. 21°C/70°F you shouldn’t need any additional heating, the warm substrate and the walls of the enclosure should prevent any drastic drop of your temperature during nighttime. Otherwise I would use a small RHP as backup heating.
__________________
1,0 Lampropeltis triangulum campbelli, 1,2 Gonyosoma oxycephalum, 1,2 Philodryas baroni, 1,2 Spilotes pullatus, 2,1 Spilotes sulphureus, 0,1 Gonyosoma boulengeri, 1,1 Zamenis longissimus, 0,1 Malpolon sp., 1,1 Malpolon monspessulanus
Roman is offline  
Login to remove ads
Old 02-11-18, 03:28 AM   #2
Shauna0522
Member
 
Join Date: Oct-2017
Location: Oregon
Posts: 172
Country:
Send a message via MSN to Shauna0522 Send a message via Yahoo to Shauna0522
Re: Want to build adult bioactive vivarium for brb

Quote:
Originally Posted by Roman View Post
I use only metal halide lights or halogen lights as heat sources for my enclosures, from 25 W to 70 W depending on the size of the enclosure. The reasoning behind this is that they create a bright hot spot. Your snake associates warmth with light, so it will look for heat at the brightest spot in your enclosure.

For your enclosure I would use a LED light as long as your enclosure (4 ft) for the ambient light and for your plants. You need enough light in the blue and red spectrum for your plants, so look for a light with 6500k. For heat and UVB place a 70W UV emitting metal halide lamp on top of your enclosure over some mesh. This lamp will provide a heat spot of ca. 30°C/86°F and creates a thermal gradient to the other end of your enclosure where the temperature will be room temperature (or slightly higher). Here in Germany we have a brand of lights which also offers a “flood” version with a wider focus, so the heat and UVB are not tightly focused but a bit wider spread.

Whether you need any additional heating depending on your ambient room temperatures (especially during winter). If your temperatures doesn’t drop below ca. 21°C/70°F you shouldn’t need any additional heating, the warm substrate and the walls of the enclosure should prevent any drastic drop of your temperature during nighttime. Otherwise I would use a small RHP as backup heating.


Quote:
Originally Posted by Jim Smith View Post
I highly recommend RHP with a good thermostat for your enclosure. It will heat your enclosure evenly and are much safer than most heating systems. I also recommend ProProducts heat panels (here's a link to their website) Pro Products – Specialized Habitat Control Products They will discuss your needs based on the enclosure size, reptile intended to he housed etc., and custom make the RHP for your enclosure. It takes about 15 minutes to install an RHP with four small bolts to the ceiling of your enclosure. You might also want to consider using HDPE for your enclosure. https://www.professionalplastics.com...SAAEgI3qPD_BwE Super easy to work and you can use regular woodworking tools. Completely waterproof and MUCH lighter than plywood, especially 3/4 birch plywood. If you want a wood look to the front of your enclosure, you can easily add 3/8" wood flooring pieces in whichever wood/finish you want. You can get the wood flooring anywhere, even on Craig's list for cheap. Just some thoughts...
Thank you to you both you definitely have given me something to think about I appreciate the help.
__________________
1) 1 Brazilian Rainbow Boa (Shikah), 2) 2 Dogs, 1 Rotterman (Chewbacca) 1 Dachshund (Cricket) 3) 2 Horses, 1 Arabian/Paint (Sierra) 1 Tennessee Walker/Paint (Oakley) 4) 1 Leopard Gecko (Lavender)
Shauna0522 is offline  
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 05:01 PM.

Powered by vBulletin®
©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 2002-2026, Hobby Solutions.

right